Testors 1/32 Kaman H-43B Huskie Helicopter

[DavidsScaleModels]

**************This was listed as 1/48 - Turns out the model is actually a 1/32 scale. Testors mis-printed their box as 1/48!********************
This build is using an old kit made by Testors. Testors was known for doing some of the unique subjects over the years. This is their 1/32 scale H-43B Huskie helicopter. It was originally released in 1961 and re-issued in 1967 to include Viet Nam parts. This version I am building is the final release of the kit in 1998. The Kaman Aircraft H-43B Huskie is a very distinctive helicopter. It uses twin main intermeshing rotors. These were counter-rotating so a tail rotor was not required. It was first flown in 1953 and was in service until the early 1970's. During the Viet Nam was it was utilized as an Air Rescue and Recovery helicopter which were part of the Pacific Air Rescue Center.

I started off working on the interior. The kit does not provide any details. I obtained a lot of reference photos online. The bulkhead between cockpit and crew area was the first part I started detailing. It required mold marks to be filled with putty first. Then using styrene sheets and some photo etch pieces from my spares drawer I added the center post and details to the crew side. I used cloth tape to replicate the padding on the cockpit side. The instrument panel and center console was assembled and detail painted. I used the kit decal for the instrument panel as it matched very well to the reference photos. Next I then test fit the interior to the fuselage and marked where everything lined up so I can detail the insides. The kit also does not include the roof for the crew cabin and the overhead console for the cockpit. I used some sheet styrene shaped for the roof then scribed the panel lines and rivet lines to add detail. The crew area also has an overhead light which I replicated by drilling a hole and installing a clear lens.

While measuring for the roof I realized the fuselage has two screened intakes molded in for the engine intakes. I cut these out and replaced them with some fine metal screening. There is also a section in the forward post that in the reference photos is open and the kit had these molded closed so I opened these up. Finally I worked on the cockpit seats. The rear of the seats was open so I used sheet styrene to make the backs. After painting them I then made the seatbelts from cloth tape and attached some photo etch buckles. Next I will be working on the overhead console for the cockpit and detailing the interior of the fuselage halves.



You can see all the photos and details from the start in the build log at: https://davidsscalemodels.com/build-log/1-32-kaman-h-43b-huskie-helicopter/

 

[BarleyBop]

two screened intakes

... the screening makes such a huge difference!

To me, when a detail provides a proper affordance (it gives appropriate hints of its function), it seems so much more real!

A grill that air can actually flow through, a door handle that looks like it can be grasped and turned ( as opposed to molded on), a cleat that could have thread (scale rope) wrapped around it, a fire hose that has been folded and stacked.
I like seeing how you approach these details, because at scale, it often requires some ingenuity to replicate objects, given the physical properties and limitations of the materials we modelers have to work with.

 

[Jakko]

Testors mis-printed their box as 1/48!

At least they corrected it for the next print run

 

[DavidsScaleModels]

The second week of the H-43B Huskie was spent starting the super detailing of the interior. After finishing the cockpit area and installing the screens on the fuselage I installed the kit interior. I then started detailing the crew area by using sheet styrene for the supports on the port side. I then used two paperclips to replicate the pipes that run along the side. I installed the top panel and used some putty to blend it to the kit section.

While waiting for the putty to cure I used some styrene square rods to detail the framework on the rear doors and a strip of sheet styrene for the lower braces.

I am working on the details between the supports and then need to detail the rear section benches and floor. Once these are done I can paint the port side and start adding the wiring that goes on the port side. I am hoping to start on the starboard side by the end of this coming week.

You can see all the photos and details from the start in the build log at: https://davidsscalemodels.com/build-log/1-32-kaman-h-43b-huskie-helicopter/

 

[DavidsScaleModels]

The third week of the Huskie I worked on detailing the aft section of the interior. First I panted the interior of the rear doors. The lower section is red and the upper section is the interior grey. Then using styrene square rods I framed the rear edge and drilled out the holes. The port side of the interior was also painted with the grey. The reference photo shows a cutout in the floor so using some sheet styrene I made the side extensions. There are two rows of seats along the rear sides with a cargo net type of back. I used some cloth tape to make the netting. I am now working on making the seat frames out of round styrene rods and will use cloth tape for the seats.

I still have more details to add to the port side but I needed to order some more sheet styrene for the shelves that need to be added and still make the wire cables. Then I can start on the starboard side details.

You can see all the photos and details from the start in the build log at: https://davidsscalemodels.com/build-log/1-32-kaman-h-43b-huskie-helicopter/

 

[BarleyBop]

cloth tape to make the netting

Nice! Is that the fiberglass type or medical?
I've used both, and found that as long as I was careful to make clean cuts lengthwise (along the grain so to speak), it won't fray.